Nail Pullers / Hand Tools - Page 3 - Mega Sale! Save up to 29%


Mega Sale! Up to 29% off on Nail Pullers (in Hand Tools) at Oahu Handyman, Page 3 [113]. Top brands include PacTool, DEWALT, Shark Corp, Vaughan & Bushnell, Estwing, Narex, ATP, Unknown, Tao tao family, UJ Ramelson Co, & Toolco Inc.. Hurry! Limited time offers. Offers valid only while supplies last.



PacTool International RS501 Roof Snake, Shingle Nail Puller, Roof Shingle Installer (Renewed)
By PacTool
In Stock
$31.34

mpn: RS501-cr, ean: 0723548752131,

4.6 out of 5 stars with 31 reviews
YOUR BEST FRIEND FOR ROOF SHINGLE REPLACEMENT! The Roof Snake makes replacing composition shingles safer, easier and more accurate than traditional methods. PATENTED OFFSET NAIL-SLOT FEATURE -Unique design helps you align roofing nails with the proper one-inch offset from the bottom edge of your the existing course. DAMAGE-FREE SHINGLES - Replace and install 3-tab shingles without over-bending or striking surrounding shingles (or fingers!) with your hammer. CLAW TIP - Shingle nail puller claw re


Dewalt DWHT55524 10 in. Claw Bar
By DEWALT
In Stock
$19.80
$19.59
You Save: 1%

mpn: DWHT55524, ean: 7241870799097,

4.8 out of 5 stars with 36 reviews
DeWalt Nail Puller - Nail digger exposes the head of a flush nail so it can be pulled with minimal damage to the wood. Extra-wide strike surface helps user accurately strike the bar to get under a nail or behind material to pry. I-beam shaft provides strength without adding weight. Pointed penetration end digs into material to remove embedded nails. 2 nail slots. - Dimensions: 10 In. L, Pkg Qty: 1, Package Type: Hang Tag CANCER AND REPRODUCTIVE HARM www.P65Warnings.ca.gov -Taiwan.


Shark Corp 21-2016 Hardened Steel Alloy Nail Pullers
By Shark Corp
In Stock
$13.00

mpn: 21-2016, ean: 6919289910822,

4.9 out of 5 stars with 55 reviews
All SharkGrip nail pullers and prybars are forged from the finest heat-treated Japanese alloy steel; the nail-pulling and prying ends are double-tempered for added strength. The pulling ''V'' is hardened to a Rockwell 50-52 hardness, then hand-finished for accuracy. The resulting tool is so strong it can even bite into hardened and stainless steel nails. SharkGrip nail pullers pull from the shank of the nail, not the head. SharkGrip Japanese ''cat's paw''-type nail pullers have been the choice o


Vaughan & Bushnell BC10 10-1 & 2-Inch Bear Claw Nail Puller
By Vaughan & Bushnell
In Stock
$16.49
$12.86
You Save: 22%

mpn: BC-10, ean: 0051218570274,

4.9 out of 5 stars with 34 reviews
This item is Vaughan & Bushnell BC10 10-1 & 2-Inch Bear Claw Nail Puller . Used for Handtools & Tool Organizers, Nail Pullers. The produt is manufactured in United States.This item is Vaughan & Bushnell BC10 10-1 & 2-Inch Bear Claw Nail Puller. Used for Handtools & Tool Organizers, Nail Pullers. The produt is manufactured in United States. Designed for easy wedging and minimal wood damage. Forged and tempered steel. Rocker head provides excellent leverage. Black, rust resistant finish. 10-1/2''


Shark Corp 21-2220 8-Inch Prybar and Nail Puller
By Shark Corp
In Stock
$16.99
$12.46
You Save: 27%

mpn: 21-2220, ean: 5915903758963,

4.4 out of 5 stars with 46 reviews
This Pry Bar And Nail Puller Is Made With High-Quality Hardened Steel Alloy And The Thinnest Blade Available On The Market. It Will Pry Into Any Tight Spot With Ease, Doing Less Damage To Wall And Molding Surfaces. The Curve Of The Blade Is Designed To Lift Molding Easily With A Turn And Is So Sharp It Removes Any Nail, Even Very Small And No-Head Nails, Lodged In The Wall Or Any Other Material. Made With Chromium High Carbon Steel And The Thinnest Blade Available. Wide Blade Yields Less Damage.


Shark Corp 21-2036 14-1/8-inch Nail Puller
By Shark Corp
In Stock
$26.50
$24.10
You Save: 9%

mpn: 21-2036, ean: 0008023120361,

4.4 out of 5 stars with 31 reviews
All Sharkgrip Nail Pullers And Prybars Are Forged From The Finest Heat-Treated Japanese Alloy Steel; The Nail-Pulling And Prying Ends Are Double-Tempered For Added Strength. The Pulling ''V'' Is Hardened To A Rockwell 50-52 Hardness, Then Hand-Finished For Accuracy. The Resulting Tool Is So Strong It Can Even Bite Into Hardened And Stainless Steel Nails. Sharkgrip Nail Pullers Pull From The Shank Of The Nail, Not The Head. Sharkgrip Japanese ''Cat’S Paw''-Type Nail Pullers Have Been The Choice


Estwing Pro Claw Nail Puller - 14" Pry Bar with Forged Steel Construction & No-Slip Cushion Grip - PC360G
By Estwing
In Stock
$19.97

mpn: PC360G, ean: 0743153712221,

4.3 out of 5 stars with 58 reviews
Estwing’s popular 14 in. Japanese pattern design Pro-claw nail pullers are made with fine tool steel, drop forged and tempered for extra durability. Chrome finish and comfortable blue cushion grip. Both nail puller claws are precise and sharp to remove imbedded or headless nails with ease and minimal wood damage. Shape and rounded head design gives you improved leverage. Precision thin claw design enables you to get into hard to reach places. For use in nail removal right angled for removing e


Narex Tack Lifter Upholstery Staple Remover with Beech Wood Handle
By Narex
In Stock
$12.99

mpn: 879050, ean: 0616909150847,

4.7 out of 5 stars with 41 reviews
This tack lifter is made by a small tool manufacturer in the Czech Republic and is of exceptional quality. It has 5/16'' (8 mm) diameter blade that flares to produce the tongue. Tongue is ground and not stamped or molded. The blade if made from carbon steel which is hardened and tempered. Handle has a metal ferrule to withstand torque. Overall length is 8''.Made by a small tool manufacturer in the Czech Republic. Has a 5/16'' (8 mm) diameter blade that flares to produce the tongue. Tongue is gro


ATP Blind Inner Bearing Puller Slide Hammer Set Hole Remover Extractor Set 5PCS
By ATP
In Stock
$31.99

mpn: A0009, ean: 0687926000088,

4.2 out of 5 stars with 43 reviews
ATP Blind Inner Bearing Puller Slide Hammer Set Hole Remover Extractor Set 5PCS Bearing Extractor Collets With Internal Capacity From 3/8'' (10mm) To 1-1/4'' (32mm) One Slide Hammer Assemble & ClampOpen Clamps By Turning Handle Clockwise To Snug Against The Bearing For Pulling Out Evenly Without Damage The Parts Fully Chromed Carbon Steel Open clamps by turning Handle clockwise to snug against the bearing for pulling out evenly without Damage the partsBearing Extractor Collets With Internal Capa


Shark Corp. 21-2023 Hardened Steel Alloy Nail Pullers
By Shark Corp
In Stock
$14.50
$10.35
You Save: 29%

mpn: 21-2023, ean: 5448095633577,

4.3 out of 5 stars with 42 reviews
Hand-Sharpened, Double-Tempered Chromium High Carbon Steel Blade Will Bite Into Any Part Of Nail Including Headless Nails. 9'' Long.Hand-sharpened, double-tempered chromium high carbon steel blade will bite into any part of nail including headless nails. This product is easy to use easy to install and highly durable. Item is manufactured in China. Hardened ''V'' takes a positive bite into the nail's shank for easy removal. Curved underside easily slides under an embedded nailhead or onto the nai


Bc-8 11-Ounce 7.75-inch Bear Claw Nail Puller Multi Color Metal
By Unknown
In Stock
$60.99
$50.99
You Save: 16%

mpn: Misc, ean: 0300876038344,

4.2 out of 5 stars with 8 reviews
Forged, tempered steel with flat claw for easy wedging and minimal wood damageRocker head gives excellent leverageBlack, rust resistant finish7. 75-inch length11 ozCardedMaterial: MetalColor: Multi.Specs:Material : MetalColor : MultiDimensions : 1 inches high x 2 inches wide x 8 inches longBc-8 11-ounce 7.75-inch Bear Claw Nail Puller Multi Color Metal. Material : Metal. Dimensions : 1 inches high x 2 inches wide x 8 inches long.. Forged, tempered steel with flat claw for easy wedging and minima


4" / 100mm Gear Hub Flywheel Bearing Puller 2 or 3 Leg Internal External
By Tao tao family
In Stock
$65.29

mpn: Ttfus-2686, ean: 6401128474010,

4.5 out of 5 stars with 30 reviews
Professional tool for commercial or occasional use 2 and 3 leg gear pullers Manufactured from alloy steel for strength and durability Extra fine thread on the mandrel helps to exert more force when required High quality puller suitable for gears, pulleys, flywheels etc Legs adjustable up to 4'' depth Ideal for removing gears, sprockets, bearings and pulleys etc Fits gears and wheels up to 4'' (100mm) in diameter The puller has a long bolt with a sharp point / tip on one end and on the other a he


C.S. OSBORNE # 600, 787A Staple Puller Side Cutter Remover - DIY Upholstery Tools Set of 2 - Made in the USA
By UJ Ramelson Co
In Stock
$56.35

mpn: 787A600,

4.7 out of 5 stars with 24 reviews
C.S. Osborne Staple Puller #600 & 787A - Forged steel. Vinyl handles to add comfort. 600 - (Green Grips) - Nose of the plier is bent at the right angle to go under the staple, grab it and pull it out. C.S. Osborne Staple Puller #787A - Side Cutter Forged steel with extra long. pointed cutter. Polished head, vinyl handles. Depth of head aids removing staples.This is the famous European ''Vienner''. Made in the USA✅ #600 - Nose of the pliers is bent at the right angle to go under the staple, gr


Hydraulic 10 Ton Ram Rod Gear Hub Puller Separators Set TE059
By Tao tao family
In Stock
$106.68

mpn: Ttfus-2081, ean: 6401128467968,

4.3 out of 5 stars with 12 reviews
Professional tool for everyday or commercial use. Screw mechanism converts power to 10 tonne ram head with enough force to remove most stubborn bearings / pulleys and shafts. Fits any 10 tonne gear puller set by any make. Suitable for pulling hubs, flanges, gears and bearings. 10 Ton Hydraulic power unit with tommy bar. The ram weighs about 2kg which helps to substantiate it's quality and durability. TOTAL DIMENSIONS OF THE RAM : Length of the ram excluding the handle 190mm Diameter of the ram 4


Set of 4 slammer hammer (Heavy Duty, Large, Small, Mini) with Deluxe Vise Grips
By Toolco Inc.
In Stock
$236.13
$227.80
You Save: 4%

mpn: S3-DVG005, ean: 0611856382372,

4.0 out of 5 stars with 47 reviews
Toolco's Slammer Hammer can be used for many different projects. It is good for pulling nails, body and dent puller, flywheel puller, cotter pin puller, dowel pin puller, moon key puller, door hinges, snowmobile track sliders, and tent stake remover and MANY more!! This is a set of 4 slammer hammers (heavy duty, large, small, and mini) and the DELUXE vise grips to go with them.Mini Deluxe: 5'' wr. Small Deluxe: 7'' r. Large Deluxe: 10'' r. Large HD Deluxe: 10'' r. Slammer hammers can be used to



Viewing Page 3 of 3

Browse Our Catalog




Privacy Policy / Terms of Service / Accessibility Statement
© 2019 - oahu-handyman.com. All Rights Reserved.